Jet Mill for MICA is an industrial equipment. With the development of society and the needs of people's lives, the industrial community is getting bigger, fine, purity, and pass rate requirements for various fine powders. The higher, the application of the classification machine is also more extensive.
Jet Mill for MICA should be installed in a place where the site is flat. Pick the processed material before work, no metal, stone, etc. hard substances are mixed into the machine, so as not to damage the parts or failures in the machine. Check that each component is firm and reliable before booting. Everything is normal, the side can turn on the power, idle for 1-2 minutes, check whether the operation is normal, everything is normal, it can be pushed. When working, the operator cannot leave. Once the sound is abnormal, the power should be disconnected immediately. When machining raw new friends Chinese medicine crusher, the discharge opening should be tied to the bag. When the pulverizer is in use, if you encounter the power supply voltage, do not use it, so as not to damage the motor. When the power supply voltage is normal, the machine is not easily damaged, and the production efficiency is high.Jet Mill for MICA Main performance characteristics:
1, using vertical hierarchical devices, the product particle size is adjustable between D97: 8-150 microns, good particle shape, narrow particle size distribution. It can be used in series with multi-stage classifiers and produces a product having multiple particles.
2, the device is easy to disassemble, the inner wall is smooth, no dead angle. The entire system is closed, the dust is small, low noise, and the production process is clean and environmentally friendly.
3, the control system is controlled by program control and easy to operate.
Do you know how do you use Jet Mill for MICA? I hope the content below can help you.
1. Preparation before the pulverizer is started to check whether the host, joint, pipeline, and the valve are normal and working properly.
(1) Open the compressor power supply, dustpress pressure valve and the main air valve, open the power switch of the pulverizer, turn on the power switch.
(2) From zero, gradually adjust to the specified speed.
(3) Open the fan, cyclone separator, dust removal and charger power, open the total power box, set the frequency of the inverter, and then start charging.
(4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel.
3, pulverizer shutdown sequence is: inverter - feeder - main valve compressor - Compressive plane impeller motor - cyclone material, dust removal switch - fan - General power supply air compressor.
4, eddy current pulverizer maintenance and maintenance
(1) Periodically lubricate the eddy current pulverizer, but the lubricating oil should not be too large to prevent too high of the bearing temperature.
(2) Check the impeller,The wear of the screw conveyor and the crushing nozzle is very important.
(3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect.
(4) After the filter bag is filtered, it should be cleaned or replaced.
5, eddy current pulverizer precautions
(1) When the device is running, the unloading port cannot be reached, and the accident occurs.
(2) The rotational speed of the impeller should not exceed the specified requirements, otherwise the temperature is too high, the impeller and the electric chance are damaged.
(3) Regularly check the safety valve to ensure safety.
ALPA cerium oxide Jet Mill for MICA case sharing: The customer is an research institute in a well-known country in China, and the cerium oxide is ultrafinely pulverized during the study. The Jet Mill for MICA of our AlPa was purchased.
Cerium oxide mechanical grinding machine technical parameters:
Finished product granularity: 200-2000 mesh
Production capacity: 10-30kg
Shan dong alPA has been working hard as a crusher Customers provide greater value, the fineness, production capacity, and installation venues of each project are important information for custom selection, pre-sales service, 24-hour online customer service to answer questions, provide the ideal crusher production line to solve The plan is provided, and the factory offer is provided, and the cerium oxide crushing project is increased.
Shan dong alpa is a well-known particle and powder processing system supplier, which is committed to the transformation of traditional powder industries. We provide customized and passed CE certified products: airflow pulverizer, mechanical pulverizer, airflow classifier, ball milling production line, surface modification production line, etc. In the field of medical, food, chemical, minerals, new materials, solid waste treatment, we have a mature full-specific solution. We provide more than just machines. We help you design the ideal system to meet your needs. In the past 20 years, \"the future\" of the advanced materials in powder technology \"has always been our company mission. We look forward to and desire to embrace the future. To this end, we have made full preparation. We wish to grow together with you.
