Steam Jet Mill Grinder for Foaming Agent is one of the common ultra-fine shredded methods, widely used in ultra-fine pulverization or fine pulverization of materials such as non-metallic mines, drugs, chemicals, metallurgical and other industry, with product particle size, particle size distribution Narrow, smooth surface surface, particle rules, high purity, high activity.
Steam Jet Mill Grinder for Foaming Agent technology is designed and manufactured in the center of grading.
There are usually two classification wheels: metal and ceramics, for some magnetic pollution-sensitive materials, the ceramic grading wheel must be used, and the current market is commonly used in the market. Another silicon nitride ceramic has excellent machining properties, high temperature resistance, corrosion resistance, wear resistance, high strength, high adhesion, low density, low friction coefficient and self-lubricity.
The grading wheel can be widely used in powder refining and grading industries. At present, the maximum diameter of φ180 mm is currently reached, the highest operating speed is 12,000 rpm, and the normal service life is more than 1 year. It has been successfully applied to Downstream users, the application is good. The maximum use of this classification wheel is to prevent metal pollution, in addition, its specific graviz is 40% lower than zirconia ceramics, which can not only greatly reduce the energy consumption of the motor, but can greatly lower motor energy consumption. Under existing motors, overcons can be achieved to obtain finer particles.
Steam Jet Mill Grinder For Foaming Agent Principle: When the compressed gas enters the pulverizer by the feeder, the pulverized raw material enters the pulverizer, there are multiple pulverized nozzles in the pulverized chamber, and the supersonic air flow is injected, so that the material is affected by the gas stream. High-speed shock and material collision, friction, and pulverized, the grading tube separates the thicker particles, the crude particles are circulated to the pulverizing chamber to continue pulverizing, after the interior closed circuit circulation is pulverized, and finally the distribution of uniform dispensing in the discharge port. . 1. Suitable for dry ultrafoil. Due to the large impact speed, it can reach 2.5 Mach or more. It is easy to obtain 1-10 micron particles, depending on the material properties, it is possible to obtain less than 1 micron particles. 2. Because there is a closed-circuit classification mechanism inside the pulverizer, the product is thick The particles are constantly pulverizing, and therefore the particles are uniform, small particle size distribution ranges are obtained. 3, the device has short-striped time, simple structure, convenient operation, small area, low noise (72 decibel) and no vibration. 4, the efficiency of the pulverization is high, which can be pulverized, and the purity of the pulverized article can be maintained.
Let's talk about how to properly use Steam Jet Mill Grinder for Foaming Agent
1. Prepare check hosts, attachment machines, pipelines before bootWhether it is intact, whether it is working properly.
Second, open
1. Turn on the compressor power supply, the pressure valve and the main valve of the dust collector, then turn on the power switch of the powder machine, and turn on the power.
2. From the zero start grading wheel and gradually adjust to the specified speed.
3. Several turning wind turbines, cyclone separators discharge, dust removal, feed motor power, and then turn on the total power supply of the tube bar, set the inverter frequency, and then begins to break.
4. The particle size of the finished wheel can be adjusted by grading wheel frequencies and charging.
Third, the order of shutdown is: inverter - feeder - Main valve - Compressor - Stepper wheel Motor - Cyclone discharge, dust removal switch - Fan - Total Power - Air Compressor.
4, repair
1. The motor should be lubed regularly, but the grease should not be too large, the bearing temperature is too high.
2. Hierarchical impeller, spiral feeder, crushing nozzle wear should pay attention to check, belt tight and suitable.
3. After a crushing material, after a certain period of time, it is necessary to remove the viscosity of the chalk, so as not to block, thereby affecting the crushing effect.
4. After the filter bag, you should clean or replace it.
V. Note
1. When the discharge device is running, the unloading port cannot be extended to avoid accidents.
2. The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric machine are damaged.
3. Regularly check the safety valve to ensure safety.
ALPA Trimata Steam Jet Mill Grinder for Foaming Agent Case Sharing:
A electromechanical company is mainly dedicated to production equipment such as push bokeh, roller furnace, mesh furnace and other products. New energy batteries, electronic components and other fields. The company has always adhered to the principle of \"people-oriented, innovation first\". The company has established a good relationship with multiple international companies. With exquisite technology, we will have our customers' support and trust. We will give back to our customers with quality products and services to make better contributions to electromechanical needs.
Case parameters:
Product particle size: D50: 15μm
Hour Yield: 600kg
Please pay attention to Shan Dong Alpa, the company mainly airflow mill, air flow grinding, medical airflow Crusher, disk airflow pulverizer, eddy current pulverizer.
