Most of the product production and processing in the current stage use Jet Mill for Plant ASH to use Jet Mill for Plant Ash, which is a very common way of processing, accompanied by the continuous improvement of scientific productivity, and the technology of grading equipment It is also imminent to replace. The performance and internal configuration of the grading device of the airflow must also keep the trend of the era to continue the upgrade of the product.
Crushing product except for particle size, there is also a narrow particle size distribution, smooth particle surface, particle shape regular, high purity, high activity, good dispersibility. Since Jet Mill for Plant Ash creates a Juromon cooling effect during the crushing process, it is also suitable for low melting point and ultrafine pulverization of thermal materials. Jet Mill for Plant ASH The gas ratio in the pulverization process is an important technical parameters and important indicators.
If the gas is too small, the kinetic energy of the airflow will be insufficient, which will affect the fineness of the product. However, if the gas ratio is too high, not only waste energy, but even the dispersion performance of certain particulate materials will also be deteriorated.
When the particle size of the feed is smashed, the particle size of the feed is more stringent. In the case of titanium powder, when pulverizing the calcined material, it is necessary to control 100-200 mesh; the material after the pulverization surface is generally 40-70 mesh, and cannot exceed 2-5 mesh.
The turbine grading system set in the classification room can obtain a powder of micrometers or even finer. When the pulverized material is pulverized in the pulverized chamber, the same particles at the edge of the turbine will be attached to the two different effort of the centrifuge field (i.e., centrifugal force and airflow resistance generated by turbine). When the particles are large, the centrifugal force is greater than the resistance, and the large particles fly toward the chamber pool wall along the turbine tangential direction, and then returned to the pulverizing chamber to be re-pulverized. When the particles are small, at this time, at this time is less than the resistance, the small particles enter the interior of the turbine with the rising airflow, and collectively collected by the cyclone to qualified products.
Jet Mill for Plant ASH Job Safety Application Basic Requirements
2, pulverizerAnd the power unit should be installed firmly. If the equipment is fixed for a long time, it should be fixed on the cement; if the device is a mobile operation, the unit should be installed on the base made of angle iron, and ensure that the belt wheel groove of the power machine (diesel or electric motor) and the equipment is in the same Rotary plane.
At the same time, check if the leather belt looseness is appropriate.
4 Whether the power machine and the pulverizing machine are lubricated.
5, don't just replace the pulley, prevent the transition chamber to produce explosion, or the speed of the pulverizer is too low.
6. After the pulverizer starts, it should be idled by 2 to 3 minutes, no abnormal phenomenon, then press the work.
7. At any time, pay attention to the operation of the equipment, the feeding should be uniform, to prevent blocking bullies, do not have a long time overload. If there is found that vibration, noise, the bearing and the body temperature is too high, the outer spray, etc., should be closed immediately, and the fault can be eliminated.
8. When blocking occurs, it should be stopped immediately. It is strictly forbidden to use a wooden stick or hand to feed or pull out the feed to avoid the pulverizer to wound the arm or damage the machine.
9. If you crush a hard raw material, the operator must wear glasses.
10, the workplace should have a ventilator and strictly prohibit fireworks to prevent dust explosion from fire.
ALPA CD Jet Mill for Plant Ash case Sharing: This customer is a large-scale comprehensive group enterprise specializing in the mining, powder processing and sales of heavy crystalline mines, which is before. Imported crystal stone crushing equipment from abroad. Later, by understanding, knowing the ultrafine pulverization equipment of our ALPA Co., Ltd., in terms of performance, in terms of foreign devices, far exceeding the same type of equipment, far exceeded the same type of equipment. Finally, after many inspections, Jet Mill for Plant Ash was purchased from our company.
Finished granularity: 1250 mesh
Production capacity: 1.2-1.5T
Shan dong alpa as a 20-year powder engineering equipment manufacturer, with more than 3,000 domestic and foreign Home customers, rich research and development and production experience will always lead to the front end of the industry, so before consulting, you need to provide the characteristics of the crushing materials, the granular parameters, production and production yield, purity requirements, specific process requirements (anti-high temperature, explosion-proof, anti-proof Dust pollution, etc.), professional engineers provide appropriate equipment models or system solutions according to this information. Welcome to inquire.
