Modern production not only pursues production and finished product quality, but also develops toward environmental protection. Especially in the comminution industry, the overall development trend of Steam Jet Mills for Plastic Additives technology in China is the stable development of the Steam Jet MillS for Plastic Additive, strong, high quality, high quality.
Steam Jet Mills for Plastic Additives has a small size, light weight, high efficiency, no dust, clean, easy to operate, and aesthetics. The pulverized tank and the blade are manufactured by stainless steel. It can complete the crushing and fine powder in 3 seconds - 2 minutes. It can quickly crush a variety of Chinese herbal medicines and most of the food, wide and wide, and different nature materials can be very smashed. Loss, smash different materials will not be stronger. Such as Western ginseng, ginseng, three seventh, placenta, flyer, pearl, white peony, 苡 苡 米, green beans, soy, sesame, rice, corn, etc. The host and the grading flow bearing are lipomatic lubrication, using special lipids, the replacement period of the bearing is around three months, and the filling of the grease is 1/2 of the interior space in the bearing cavity. Otherwise, It will cause too high of the bearing temperature. The spiral feeder has changed the lipid period of half a year, and Cape Calcium-based grease.Ultrafine Steam Jet Mills for Plastic Additives Working Principle: Ultrafine Crusher Troubles in the feed port spiral feeder, the material is sent into the crushing chamber between the body and the guide circle, rotating at high speed in the comminution. Under the blade impact, the material is attached to the gel fixed to the body, resulting in impact, shearing, and material, the material and the blade, the mutual collision, friction, and shear inter alternate. After the powder, under the tension of the negative pressure airflow, the small powder grains overcome self-weight, the over the guide circle with the gas flow, and enter the grading chamber. The fractionation impeller consists of the blade, and the high-speed rotating blade produces a centrifugal force opposite to the negative pressure, and the powder particles in the leaf can be subjected to a negative pressure gas stream and the granularity of the granules, the centrifugal force generated by the impeller, and the particles are larger than the critical diameter ( The granular particles of the grading particles are large, and the pulverized chamber continues to be pulverized, and the particles smaller than the critical diameter are discharged through the drain tube into the whirlwind collector. The higher the rotation speed of the hierarchical impeller, the finer the graded particles, and the rotation of the orthogonal impeller is the determinant of the size of the particle size.
Ultraflight Steam Jet Mills for Plastic Additives is a wide-ranging device that uses air separation, heavy polishing, and shear. It is widely used in various industries. Let's take a brief introduction to its daily maintenance content.
1, when the bearing oil is high, it is necessary to stop checking the cause of the fault and removal immediately. 2, easy to wear parts should pay attention to the degree of wearAt any time, pay attention to and do the preparation for replacing the wear part.
3, for the top surface of the chassis of the active device, it is necessary to remove dust and other debris avoiding the machine that cannot be broken, the active bearing cannot move on the chassis, causing an accident.
4, all loads of the machine are bearings, so good lubrication and bearings have a large relationship, it can directly affect the service life of the machine and the operating rate, so the amount of lubricating oil required to be injected should be reached. Good seal.
5, the sleeper installed is easy to loosen, and it must be checked frequently.
6. Note that the operation of each part of the machine is normal.
7. If the rotating gear is in operation, if there is a hitting sound, it should be stopped in time and remove the fault.
ALPA Battery STEAM JET MIET MIET MIETS for Plastic Additives Sharing:
Case parameters
Product particle size: 2-45 um
Hour Yield: 200-300kg
Shan dong alpa is a 20-year experience manufacturing company with Steam Jet Mills for Plastic Additives equipment. Have multiple patents, welcome to inquire!
