Steam Jet Mills of Pine Bark This product technology has received extensive attention from the industry. Steam Jet Mills of Pine Bark is mainly used to determine its wide range of applications, high fine, typical materials: super hard diamond, silicon carbide, metal powder, high purity requirements: ceramic pigment, medicine, biochemistry, medicine . Steam Jet Mills of Pine Bark converts the normal gas from the gas source portion to nitrogen, carbon dioxide, etc., is an inert gas protection device, which is suitable for use in flammable and explosive, oxidized materials.
Crushing product except for particle size, there is also a narrow particle size distribution, smooth particle surface, particle shape regular, high purity, high activity, good dispersibility. Since Steam Jet Mills of Pine Bark generates a Juromon's cooling effect during the pulverization process, it is also suitable for low melting point and ultrafine pulverization of thermal material. Steam Jet Mills of Pine Bark is an important technical parameters and important indicators during pulverization.
If the gas is too small, the kinetic energy of the airflow will be insufficient, which will affect the fineness of the product. However, if the gas ratio is too high, not only waste energy, but even the dispersion performance of certain particulate materials will also be deteriorated.
When the particle size of the feed is smashed, the particle size of the feed is more stringent. In the case of titanium powder, when pulverizing the calcined material, it is necessary to control 100-200 mesh; the material after the pulverization surface is generally 40-70 mesh, and cannot exceed 2-5 mesh.
1, can effectively reduce cost, reduce cost, suitable for low value of coarse powder.
2, simple structure, convenient maintenance, less easy to lose weight, low operating noise, low energy consumption.
3, the classification machine uses large diameter single-stage classification wheels to improve production capacity.
4, the inner wall smooth and wear, more conducive to the classification of materials.
5, use a negative pressure operation, so that it does not leak, to achieve environmental requirements.
6, running stable and reliable, its product can be uniform.
1. Preparing before booting the host, attachment machine, pipeline, and valve, whether it is intact, is it possible to work properly? .
Second, open
1. Turn on the compressor power supply, the pressure valve and the main valve of the dust collector, then turn on the power switch of the powder machine, and turn on the power.
2. From zeroStart the grading wheel and gradually adjust to the specified speed.
3. Several turning wind turbines, cyclone separators discharge, dust removal, feed motor power, and then turn on the total power supply of the tube bar, set the inverter frequency, and then begins to break.
4. The particle size of the finished wheel can be adjusted by grading wheel frequencies and charging.
Third, the order of shutdown is: inverter - feeder - Main valve - Compressor - Stepper wheel Motor - Cyclone discharge, dust removal switch - Fan - Total Power - Air Compressor.
4, repair
1. The motor should be lubed regularly, but the grease should not be too large, the bearing temperature is too high.
2. Hierarchical impeller, spiral feeder, crushing nozzle wear should pay attention to check, belt tight and suitable.
3. After a crushing material, after a certain period of time, it is necessary to remove the viscosity of the chalk, so as not to block, thereby affecting the crushing effect.
4. After the filter bag, you should clean or replace it.
V. Note
1. When the discharge device is running, the unloading port cannot be extended to avoid accidents.
2. The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric machine are damaged.
3. Regularly check the safety valve to ensure safety.
ALPA Cassava Starch Steam Jet Mills of Pine Bark Case Sharing: This customer is a new panel industry, dedicated to providing professional and excellent plywood new filler for plywood industry customers. The company needs to be used in the production process of the company. Multi-party examine, finally purchased the CSM1100-V mechanical grinder from our AlPa.
Technical parameters:
finished particle size: 98% over 325 mesh
Production capacity: 2T
Shan dong alpa is committed to Steam Jet Mills of Pine Bark, has mature craftsmanship Process, company technical strength, specializing in Steam Jet Mills of Pine Bark, survive in quality, welcome everyone to come to consult.
