EXTRA FINE Steam Jet Mill Machine is a clean, efficient, high-level, high-yield of advanced crusher model in crushing, is very extensive, from dozens of micro test to the time With a few hundred tons of large production, Extra Fine Steam Jet Mill Machine is narrow by it: the particle size distribution is narrow, the average particle size is fine; the powder is good, the product is purity; suitable for low melting point, thermal drugs; good sealable, less contamination, less pollution Easy to operate; crushing - mixing - dry online operations, etc. have been widely recognized by the company.
In terms of airflow milling, it is important to understand that its operational rules are very important, because only the operation procedures can be performed correctly.
1. The operation rules for Extra Fine Steam Jet Mill Machine are as follows: After the preparation before the boot receives the production order, prepare materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it can work properly. Whether there is a phenomenon that the material is stacked in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Extra Fine Steam Jet Mill Machine starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should be achieved, not large or small, thereby affecting the separation effect of the grinding machine, making the machine easily fail. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the close and inspection of Extra Fine Steam Jet Mill Machine are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vulnerable part. Fill in the corresponding production record, update the device status flag, which is convenient for the next time.
The working principle of Extra Fine Steam Jet Mill Machine is a complete crushing system composed of crushers and cyclone separators, dust collectors and air blowers. After the compressed air is filtered, the high-speed nozzle is sprayed into the crushing chamber, and the material is pulverized by repeated collision, friction and shearing at the intersection of the multi-high pressure airflow. The crushing material moves together with the rising airflow to the grading area with the suction of the fan. Under the action of centrifugation, the thickness of the material is separated, and the grading cyclone is required to grade the cyclone to enter the cyclone dust collector, and the coarse comminution continues to be pulverized down. Suitable for dry crushing of various materials that are less than 9 in the Moh-hardness, especially for high hardness, high purity, high value-added crushing materials. It includes a vertical classification device. The size of the product can be adjusted between D97: 8 and 150 microns, with a good particle shape and a narrow particle size distribution. Low temperature without media crushing. It is especially suitable for thermal sensitivity, low melting point, sugar-containing and volatile substances. The grinding process mainly depends on the collision of the material itself, which is different from the impact of the mechanical crushing blade or the hammer on the ground on the ground, so the equipment has high wear resistance and high product purity.
Extra Fine Steam Jet Mill Machine is widely used, do you know how to use it correctly? The following content hopes to help you.
1. Preparation before departure. Check whether the host, joint, pipeline, and the valve are normal, working properly.
(1) Turn on the compressor power supply, the dust collector pressure valve and the main air valve, open the air pulverizer power switch, and turn on the power switch.
(2) From scratch, adjust to the specified speed.
(3) Open the fan, cyclone separator, dust collector, charge motor, open the total power box, set the inverter frequency, and then start charging.
(4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel.
3, the sequence of stops is:
inverter-feeder-main air valve-compressor-grade impeller-motor cyclone material, dust removal switch-fan-main power supply-air compressor .
4, Maintenance
(1) The motor should be lubricated regularly, but the lubricating oil should not excessively avoid the bearing temperature too high.
(2) Checking the wear of impeller, helical conveyors and crushing nozzles.
(3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect.
(4) After a filter bag, you should clean or replace it.
5, Precautions
(1) When the discharge equipment is running, the unloading port cannot be reached, and the accident occurs.
(2) The impeller speed must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric chance are damaged.
(3) Regularly check the safety valve to ensure safety.
Erli Changli Extra Fine Steam Jet Mill Machine Case Sharing: The company is a high-tech industry in a industrial company, integrating mineral resources, mining, deep processing in one, main products have six categories: long Powder, silicon fine powder, aluminum soil, kaolin and other products. The whiteness is high, the particle size is fine, the particle size is reasonable, the quality is stable, widely used in electrician, electronics, silicone rubber, ceramics, precision casting and other industries. Products are exported to many countries and regions in my country. The company needs airflow selection to ultrafine long stone powder.
Finally, our classifier can meet customer needs.
Product particle size: D50: 16.7
If you still have questions, you can contact Erpa Technology Co., Ltd. directly, the company's leading product EXTRA FINE Steam Jet Mill Machine system is currently unable to handle The minor particle grading has been successfully applied, breaks through the boundaries of dry grading, equipment system in rare earth polishing powder, metal powder, silver powder, tungsten powder, alumina, battery material, ceramic powder, carbonyl nickel, iron powder, Toner, resin, paint, mica powder, cosmetics and other industries have won a wide range of applications, warmly welcome users to come to consult, our company equipment is manufactured, the size is complete, there is a suitable for you!
